GOST 8.002 86 was replaced by which one. Bodies exercising state metrological supervision

GOST 8.002-86

Group T80

STATE STANDARD OF THE UNION OF THE SSR

STATE SYSTEM FOR ENSURING THE UNIFORMITY OF MEASUREMENTS

STATE SUPERVISION AND DEPARTMENTAL
CONTROL OF MEASURING INSTRUMENTS

Key points

State system for ensuring the uniformity of measurements.
State supervision and departmental control of measuring instruments.
Basic regulations

OKSTU 0008

Introduction date 1987-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR State Committee for Standards

PERFORMERS

X. O. Malikova (theme leader), A. V. Plotnikova, V. A. Skovorodnikov, M. G. Sharonov

2. APPROVED AND INTRODUCED BY Decree of the USSR State Committee for Standards No. 388 dated February 21, 1986

3. INSTEAD OF GOST 8.002-71 in part of Sec. 1, 2, 4

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS


	Number of paragraph, subparagraph, enumeration, application
GOST 8.001-80

GOST 8.383-80

5. Reissue (November 1987) with Amendment No. 1 approved in September 1987 (IUS 1-88).

This standard establishes the main provisions of state supervision and departmental control over the development, production, condition, use and repair of measuring instruments, over the activities of departmental metrological services, over the implementation and compliance with metrological rules, including rules metrological support works carried out in all sectors of the national economy.

The standard does not apply to measuring instruments used at enterprises and organizations of the Ministry of Defense and manufactured by its orders.

1. GENERAL PROVISIONS

1.1. State supervision and departmental control over measuring instruments (state metrological supervision and departmental metrological control) are carried out in order to ensure the uniformity of measurements as necessary condition improve efficiency social production, acceleration scientific and technological progress, growth in labor productivity, increase technical level and product quality, ensuring reliable accounting of material, raw materials and fuel and energy resources, improving management efficiency in the sectors of the national economy.

1.2. The main task of state metrological supervision and departmental metrological control is to strengthen state discipline and increase the responsibility of ministries (departments), enterprises, associations, organizations and institutions (hereinafter referred to as enterprises) for the timely, implementation and strict observance of metrological rules established by current legislation, standards, instructions , rules, regulations and other normative and technical documents, for ensuring the uniformity of measurements and metrological support of work performed in the sectors of the national economy.

1.3. State metrological supervision is carried out in the form of:

state acceptance and control tests of measuring instruments in accordance with GOST 8.383-80 and GOST 8.001-80;

state metrological certification of measuring instruments in accordance with GOST 8.326-78;

state verification of measuring instruments in accordance with GOST 8.513-84;

registration of enterprises and organizations manufacturing, repairing and verifying measuring instruments in accordance with the procedure established by the USSR State Committee for Standards (Gosstandart);

inspections of the condition and use of measuring instruments, the activities of departmental metrological services in ministries (departments) and enterprises, the implementation and compliance with metrological rules (hereinafter referred to as verifications of compliance with metrological rules) in accordance with the procedure established by the State Standard.

1.4. Departmental metrological control is carried out in the form of:

departmental metrological certification of measuring instruments in accordance with GOST 8.326-78;

departmental verification of measuring instruments in accordance with GOST 8.513-84;

checks of the condition and application of measuring instruments, implementation and compliance with metrological rules at enterprises of the ministry (department) system;

inspections of the activities of the head and base organizations of the metrological service, structural divisions metrological service at the enterprises of the system of the ministry (department) in the manner established by the ministry (department);

certification of test and analytical laboratories at the enterprises of the system of the ministry (department).

Normative and technical documents of the ministry (department) may establish other forms of departmental metrological control.

1.3, 1.4. (Revised edition, Rev. No. 1).

1.5. The organization and procedure for carrying out work on state metrological supervision is established by state standards, rules, instructions and other regulatory and technical documents (hereinafter referred to as NTD) of the State Standard, which must comply with the requirements of this standard.

1.6. The organization and procedure for carrying out work on departmental metrological control is established by industry standards, rules, instructions and other NTDs of ministries (departments) and enterprises that must comply with the requirements of this standard, other state standards and NTD Gosstandart, regulating the issues of state metrological supervision and departmental metrological control.

2. BODIES CARRYING OUT STATE METROLOGICAL SUPERVISION

2.1. State metrological supervision is carried out by:

Gosstandart;

republican departments of Gosstandart in the union republics;

centers for standardization and metrology, laboratories for state supervision of standards and measuring equipment of the State Standard.

2.2. State supervision bodies carry out their functions in accordance with the established competence.

2.3. Gosstandart, in accordance with the tasks assigned to it in the field of state metrological supervision, performs the following functions:

approves standards and other scientific and technical documentation, mandatory for use by all ministries, departments, enterprises;

develops and approves, in accordance with the established procedure, work plans for state metrological supervision;

hears at meetings of the State Standard reports of the heads of ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

analyzes the results of state metrological supervision and develops measures to eliminate the identified shortcomings;

manages the activities of state supervision bodies of the Gosstandart system.

2.4. Republican departments of the State Standard, in accordance with the tasks assigned to them in the field of state metrological supervision, perform the following functions:

develop and approve work plans for state metrological supervision in the Union Republic;

ensure the organization and conduct of work on state metrological supervision in the Union Republic, continuous improvement and increase in efficiency; state metrological supervision;

organize the conduct of state control tests of measuring instruments manufactured in the republic, state metrological certification and state verification of measuring instruments, as well as registration of enterprises manufacturing, repairing and verifying measuring instruments;

organize selective inspections of compliance with metrological rules in ministries (departments) and at enterprises located on the territory of the Union Republic;

ensure the timely adoption by the state supervision bodies of the Union Republic of the necessary measures to introduce and comply with metrological rules, improve the condition and use of measuring instruments, prevent and suppress violations, as well as to bring to the established responsibility enterprises and officials guilty of violating metrological rules;

hear reports from the heads of republican ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

ensure the interaction of state supervision bodies with law enforcement and other regulatory bodies of the Union Republic;

exercise control over the activities of state supervision bodies in the Union Republic.

2.5. Centers for standardization and metrology and laboratories for state supervision of standards and measuring equipment, in accordance with the tasks assigned to them in the field of state metrological supervision, perform the following functions:

develop and approve, in accordance with the state standardization plan and on the basis of plans approved by the republican department of the State Standard, work plans for state metrological supervision at enterprises of the assigned territory, ensure an increase in the efficiency of state supervision;

carry out selective checks of compliance with metrological rules at the enterprises of the assigned territory;

organize and conduct state control tests of measuring instruments manufactured by enterprises located in the assigned territory, state metrological certification and state verification of measuring instruments, register enterprises manufacturing, repairing and verifying measuring instruments;

apply necessary measures aimed at the introduction and observance of metrological rules, improvement of the condition and use of measuring instruments, prevention and suppression of identified violations, as well as measures to bring to the established responsibility enterprises and officials guilty of violating metrological rules;

interact with law enforcement and other regulatory authorities in the assigned territory.

2.6. The implementation of the functions of state metrological supervision is assigned to specialized structural units for supervising the state of means of intention, for state testing of measuring instruments, for supervision of metrological support, as well as other units formed in the central office of the State Standard, Gosstandart departments in the Union republics, standardization centers and metrology, laboratories of state supervision of standards and measuring equipment in autonomous republics, territories, regions and cities.

The performance of certain functions in the field of state metrological supervision is assigned to metrological research and production associations and research institutes.

2.7. Officials of the Gosstandart bodies exercising state metrological supervision and acting as state inspectors for the supervision of standards and measuring instruments must be certified as a state trustee or state controller.

Certification as a state verifier is subject to persons who are entrusted with the duties of state verification of measuring instruments. These persons must undergo primary certification when they are appointed to a position, and at certain intervals - periodic certification.

Certification as a state controller (primary or periodic) is subject to persons who are assigned functions in the field of state metrological supervision in accordance with clause 1.3 (except for verification).

Primary and periodic certification of officials exercising state supervision is carried out in the manner established by the State Standard.

3. BODIES AND SERVICES CARRYING OUT DEPARTMENTAL METROLOGICAL CONTROL

3.1. Departmental metrological control is carried out by:

the ministry (department) with the assignment of these functions to the department (service) of the chief metrologist of the ministry (department);

the head and basic organizations of the metrological service of the ministry (department) with the assignment of these functions to the appropriate specialized unit;

department of the chief metrologist or other structural divisions of the metrological service of enterprises exercising control within the enterprise.

If it is not advisable to form specialized subdivisions of the metrological service in the central office of the ministry (department) or at enterprises, the functions of departmental or in-plant control should be assigned to another structural unit or responsible person appointed by order of the ministry (department) or enterprise.

3.2. Bodies and services exercising departmental metrological control in the system of the ministry (department) perform their functions in accordance with the established competence and powers granted to them by the head of the ministry (department) or enterprise.

3.2.1. The ministry (department), in accordance with the tasks assigned to it in the field of departmental metrological control:

ensures the organization and conduct of metrological control in the system of the ministry (department), systematically checks the condition and use of measuring instruments at subordinate enterprises, takes measures aimed at strict observance of the existing metrological rules;

develops and approves, in accordance with the established procedure, sectoral work plans for departmental metrological control;

approves industry standards, instructions, rules, regulations and other scientific and technical documentation that are mandatory for enterprises of its system, establishing the procedure for implementing departmental metrological control.

3.2.2. The department (service) of the chief metrologist of the ministry (department) in accordance with the tasks assigned to it, in the field of departmental metrological control:

provides and carries out in the system of the ministry (department) control over the development, production, condition, use and repair of measuring instruments, over the timely implementation and observance of the metrological rules established by the current legislation, standards, instructions, rules, regulations and other regulatory and technical documents;

ensures accounting of enterprises of the system of the ministry (department), to which the bodies of the State Standard have been granted the right to manufacture, repair or verify measuring instruments, as well as accounting of measuring instruments used at enterprises of the system of the ministry (department);

checks compliance with the requirements for departmental verification and metrological certification of measuring instruments in the system of the ministry (department);

exercises control over the timely submission by enterprises of the system of the ministry (department) of measuring instruments for state testing and state verification;

controls the work of the head and basic organizations of the metrological service, structural subdivisions of the metrological service at the enterprises of the system of the ministry (department);

gives mandatory for enterprises of the system of the ministry (department) instructions on the status and application of measuring instruments, implementation and compliance with metrological rules;

makes proposals to the leadership of the ministry (department) on the abolition of scientific and technical documentation that does not meet the requirements of state and industry standards, other scientific and technical documentation operating in the industry;

makes proposals to the leadership of the ministry (department) on the termination of production at enterprises in case of violation of metrological rules by them, non-compliance with which led to the production of non-standard products, until the violations are eliminated and on the need to take other measures in relation to enterprises and persons who have committed these violations;

exercises control over the development and implementation of measures to eliminate the shortcomings noted by the state supervision bodies.

3.2.3. The head organization of the metrological service of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides methodological guidance to the basic organizations of the metrological service of the ministry (department) on issues of departmental metrological control;

exercises control over the activities of the basic organizations of the metrological service, as well as the activities of the metrological services of enterprises of the system of the ministry (department);

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and compliance with metrological rules, at enterprises of the ministry (department) system;

organizes and conducts departmental verification and metrological certification of measuring instruments that cannot be verified or certified by the basic organizations of the metrological service;

makes proposals to the chief metrologist of the ministry (department) on the abolition of scientific and technical documentation adopted in the industry, orders, orders and instructions that contradict the current legislation, state and industry standards;

exercises control over the elimination of shortcomings identified by the Gosstandart bodies at the enterprises of the ministry (department) when they exercise state metrological supervision;

gives the heads of inspected enterprises mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

makes proposals to the chief metrologist of the ministry (department) and heads of enterprises of the system of the ministry (department) on the need to take measures against enterprises and persons who have committed violations of metrological rules.

3.2.4. The basic organization of the metrological service of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides methodological guidance to the metrological services of enterprises on issues of departmental metrological control;

controls the activities of metrological services of enterprises;

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and compliance with metrological rules at enterprises;

ensures the organization and conduct of departmental verification and metrological certification of measuring instruments that cannot be verified or certified by enterprises;

makes proposals to higher authorities on the abolition of standards and other scientific and technical documentation adopted by the heads of enterprises, orders, orders and instructions that are contrary to current legislation, state and industry standards;

renders assistance to the bodies of the State Standard in the implementation of state metrological supervision;

gives the heads of inspected enterprises mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

makes proposals to higher authorities and heads of attached enterprises on the need to take measures in the prescribed manner in relation to enterprises and persons who have committed violations of metrological rules.

3.2.5. Head of the enterprise:

organizes and exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and observance of metrological rules, activities of structural divisions of the metrological service of the enterprise;

renders assistance to Gosstandart bodies in their implementation of state metrological supervision;

approves the NTD, establishing the procedure for the implementation of metrological control at the enterprise;

encourages distinguished employees, applies penalties in accordance with the established procedure against persons who have committed violations of metrological rules.

3.2.6. Department of the chief metrologist or other divisions of the metrological service of the enterprise:

exercise control over the development, production, condition and use of measuring instruments, timely implementation and compliance with metrological rules by all divisions of the enterprise;

carry out departmental verification and metrological certification of measuring instruments within the rights granted by the Gosstandart bodies; keep records of the measuring instruments of the enterprise, draw up calibration schedules and monitor compliance with the approved schedules; coordinate with the State Standard bodies the schedules for verification of measuring instruments subject to mandatory state verification, and ensure their timely submission for state verification; develop and implement measures for the development of departmental verification of measuring instruments;

provide assistance to the Gosstandart bodies in their implementation of state metrological supervision;

develop measures to eliminate the shortcomings identified by the bodies of the State Standard and exercise control over their implementation;

give the heads of all departments of the enterprise mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

make proposals to the management of the enterprise on encouraging distinguished employees and on the need to take action against persons who have committed violations of metrological rules.

3.2.7. By order of the ministry (department) or enterprise, in accordance with the specific features of production, bodies and services that carry out departmental metrological control may be assigned additional responsibilities in the field of monitoring compliance with metrological rules and they may be granted broader rights to apply legal measures impact on offenders.

3.2.8. The heads of ministries (departments) and enterprises are responsible for the organization and implementation of departmental metrological control.

4. LEGAL MEASURES APPLIED IN THE ORDER OF STATE METROLOGICAL SUPERVISION

4.1. In cases of violation of metrological rules, state supervision bodies apply legal measures established by law to enterprises and guilty officials and issue mandatory instructions to eliminate the identified violations.

4.2. When conducting state testing of measuring instruments

4.2.1. Negative results of state acceptance tests prototype a new type of measuring instruments are the basis for refusing to approve this type and issuing a permit for the production and release into circulation of measuring instruments of the installation series.

4.2.2. The sale of mass-produced measuring instruments that have not passed state tests in accordance with GOST 8.001-80 is the basis for the application of economic sanctions in the form of transferring the entire amount of profit received by the enterprise for these products to the budget and excluding these products in kind and value terms from the reporting data of enterprises on the implementation of the plan.

4.2.3. Negative results of state control tests of measuring instruments are the basis for:

a) a ban (delay) in the release into circulation of manufactured measuring instruments;

b) application of economic sanctions;

c) disenfranchisement series production measuring instruments and cancellation of the registration certificate for the right to carry out these works.

4.3. When carrying out metrological certification of measuring instruments

4.3.1. Negative results of metrological certification of newly developed measuring instruments that are not intended for mass production are the basis for a ban (suspension) of their use.

4.3.2. The implementation of newly developed measuring instruments that have not passed metrological certification is the basis for the application of economic sanctions.

4.3.3. Negative results of metrological certification of operated measuring instruments are the basis for prohibition of their use and cancellation of the certificate of metrological certification.

4.4. When conducting state verification of measuring instruments

4.4.1. Negative results of the state verification of measuring instruments are the basis for:

a) a ban (delay) on the use or release into circulation of measuring instruments, an order to withdraw measuring instruments from circulation and operation, and, if necessary, their immediate withdrawal;

b) cancellation of impressions of verification marks on measuring instruments, cancellation of a certificate of verification or an entry on the unsuitability of measuring instruments in the technical passport of measuring instruments;

c) sealing of measuring instruments in a way that excludes the possibility of their further use;

d) appointment of a continuous one-time verification of all measuring instruments in operation, or a certain range of them in state supervision bodies;

e) establishment of reduced calibration intervals for measuring instruments in operation.

4.5. When carrying out work on state registration of enterprises manufacturing, repairing or verifying measuring instruments

4.5.1. Violation of the requirements established by standards and other RTDs for the manufacture, repair and verification of measuring instruments is the basis for:

a) refusal to issue a registration certificate for the right to perform the specified work;

b) instructions to stop these works and cancel the previously issued registration certificate;

c) exclusion from the registration certificate of those types of work for which violations were committed.

4.6. When checking the condition and application of measuring instruments, the activities of departmental metrological services in ministries (departments) and enterprises, the implementation and compliance with metrological rules, the identified violations are the basis for the application of legal measures provided for in paragraphs. 4.2-4.5.

(Revised edition, Rev. No. 1).

4.7. Particularly serious violations of metrological rules, resulting in the release of non-standard low-quality products, are the basis for mandatory orders to company officials to stop production until the violations are eliminated.

4.8. In cases where violations of metrological rules are the result of non-fulfillment or improper fulfillment by officials of the audited enterprises of the tasks assigned to them official duties, state supervision bodies have the right to submit to the relevant ministries (departments) and submit proposals to the heads of enterprises on bringing these persons to disciplinary responsibility, up to and including dismissal from their positions in the prescribed manner.

4.9. When violations of metrological rules are revealed, which, in accordance with the current legislation, are the basis for bringing the guilty officials to administrative responsibility in the form of a warning or a fine, the state supervision bodies draw up a protocol in the prescribed manner and send materials to the administrative commissions under the executive committees of district, city and district councils of people's deputies in the cities.

4.10. In cases where the violations committed through the fault of officials by their nature entail, in accordance with the current legislation criminal liability, the state supervision bodies send, in the prescribed manner, the materials of inspections to the investigating authorities.

4.11. The decision on the choice of legal measures corresponding to the committed violations of the metrological rules is made by officials of the state supervision bodies within the powers granted by the Chairman of the State Standard.

The text of the document is verified by:
official publication
State Standard of the USSR -
M.: Publishing house of standards, 1988

GOST 8.002-86 State system ensuring the uniformity of measurements (GSI). State supervision and departmental control of measuring instruments. Key points

GOST 8.002-86 State System for Ensuring the Uniformity of Measurements (GSI). State supervision and departmental control of measuring instruments. Key points

The standard establishes the main provisions of state supervision and departmental control over the development, production, condition, use and repair of measuring instruments, over the activities of departmental metrological services, over the implementation and observance of metrological rules, including the rules for metrological support of works performed in all sectors of the national economy. The standard does not apply to measuring instruments used at enterprises and organizations of the Ministry of Defense and manufactured by its orders.

Title of the document:	GOST 8.002-86*
Document type:	GOST
Document status:	It does not work(No longer valid on the territory of the Russian Federation. PR 50.2.002-94 "The procedure for exercising state metrological supervision over the production, condition and use of measuring instruments certified by measurement methods, standards and compliance with metrological rules and norms" is in force)
Russian name:	GSI. State supervision and departmental control of measuring instruments. Key points
Text update date:	01.10.2008
Date of entry into force:	01.01.1987
Date added to database:	01.02.2009
Expiration date:	01.12.2001
Developed in:	State Standard of the USSR
Approved in:	State Standard of the USSR (21.02.1986)
Published in:	Standards Publishing House No. 1988
Amendments and changes:	No. 1 dated 09/01/1987, published in the publication "IUS 1-88"
What replaces:	GOST 8.002-71(in terms of sections 1, 2, 4)
What is replaced by:	PR 50.2.002-94 The procedure for exercising state metrological supervision over the production, condition and use of measuring instruments certified by measurement methods, standards and compliance with metrological rules and norms
Table of contents:	1. General Provisions 2 Bodies exercising state metrological supervision 3 Bodies and services exercising departmental metrological control 4 Legal measures applied in the order of state metrological supervision
Located in:

Designation:	GOST 8.002-86*
Russian name:	GSI. State supervision and departmental control of measuring instruments. Key points
Status:	not valid (Outdated in the territory of the Russian Federation. PR 50.2.002-94 "The procedure for exercising state metrological supervision over the release, condition and use of measuring instruments certified by measurement methods, standards and compliance with metrological rules and norms")
Replaces:	GOST 8.002-71 (in terms of sections 1, 2, 4)
Replaced by:	PR 50.2.002-94 "Procedure for the implementation of state metrological supervision over the release, condition and use of measuring instruments certified by measurement methods, standards and compliance with metrological rules and norms"
Text update date:	01.10.2008
Date added to database:	01.02.2009
Date of entry into force:	01.01.1987
Expiration date:	01.12.2001
Designed by:	State Standard of the USSR
Approved:	State Standard of the USSR (21.02.1986)
Published:	Standards Publishing House No. 1988

STATE STANDARD OF THE UNION OF THE SSR

STATE SYSTEM FOR ENSURING THE UNIFORMITY OF MEASUREMENTS

STATE SUPERVISION AND DEPARTMENTAL CONTROL OF MEASURING INSTRUMENTS

MAIN PROVISIONS

GOST 8.002-86

USSR STATE COMMITTEE ON STANDARDS

Moscow

STATE STANDARDSOYUZ SSR

Introduction date 01.01.87

This standard establishes the main provisions of state supervision and departmental control over the development, production, condition, use and repair of measuring instruments, the activities of departmental metrological services, the implementation and observance of metrological rules, including the rules for metrological support of work carried out in all sectors of the national economy.

The standard does not apply to measuring instruments used at enterprises and organizations of the Ministry of Defense and manufactured by its orders.

1. GENERAL PROVISIONS.

1.1. State supervision and departmental control over measuring instruments (state metrological supervision and departmental metrological control) are carried out in order to ensure the uniformity of measurements as a necessary condition for increasing the efficiency of social production, accelerating scientific and technological progress, increasing labor productivity, improving the technical level and quality of products, ensuring reliable accounting of material, raw materials and fuel and energy resources, improving management efficiency in the sectors of the national economy.

1.2. The main task of state metrological supervision and departmental metrological control is to strengthen state discipline and increase the responsibility of ministries (departments), enterprises, associations, organizations and institutions (hereinafter referred to as enterprises) for the timely implementation and strict observance of metrological rules established by current legislation, standards, instructions, rules, regulations and other regulatory - technical documents, for ensuring the uniformity of measurements and metrological support of works carried out in the sectors of the national economy.

state acceptance and control tests of measuring instruments in accordance with GOST 8.383-80 and GOST 8.001-80;

state metrological certification of measuring instruments in accordance with GOST 8.326-78;

state verification of measuring instruments in accordance with GOST 8.513-84;

registration of enterprises and organizations manufacturing, repairing and verifying measuring instruments in accordance with the procedure established by the USSR State Committee for Standards (Gosstandart);

inspections of the state and application of the means of intentions, the activities of departmental metrological services in ministries (departments) and enterprises, the implementation and compliance with metrological rules (hereinafter referred to as verifications of compliance with metrological rules) in accordance with the procedure established by the State Standard.

1.4. Departmental metrological control is carried out in the form:

departmental metrological certification of measuring instruments in accordance with GOST 8.326-78;

departmental verification of measuring instruments in accordance with GOST 8.513-84;

checks of the condition and application of measuring instruments, implementation and compliance with metrological rules at enterprises of the ministry (department) system;

inspections of the activities of the head and basic organizations of the metrological service, structural divisions of the metrological service at the enterprises of the system of the ministry (department) in the manner established by the ministry (department);

certification of testing and analytical laboratories at enterprises of the ministry (department) system.

Normative and technical documents of the ministry (department) may establish other forms of departmental metrological control.

1.3, 1.4. (Revised edition, Rev. No. 1).

1.6. The organization and procedure for carrying out work on departmental metrological control is established by industry standards, rules, instructions and other NTDs of ministries (departments) and enterprises that must comply with the requirements of this standard, other state standards and NTD Gosstandart, which regulate issues of state metrological supervision and departmental metrological control.

2. BODIES CARRYING OUT STATE METROLOGICAL SUPERVISION.

2.1. State metrological supervision is carried out by:

Gosstandart;

republican departments of the State Standard in the union republics;

centers for standardization and metrology, laboratories for state supervision of standards and measuring equipment of the State Standard.

2.2. State supervision bodies carry out their functions in accordance with the established competence.

2.3. Gosstandart, in accordance with the tasks assigned to it in the field of state metrological supervision, performs the following functions:

approves standards and other scientific and technical documentation that are mandatory for use by all ministries, departments, enterprises;

develops and approves, in accordance with the established procedure, work plans for state metrological supervision;

hears at meetings of the State Standard reports of the heads of ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

analyzes the results of state metrological supervision and develops measures to eliminate the identified shortcomings;

manages the activities of state supervision bodies of the Gosstandart system.

2.4. Republican departments of the State Standard, in accordance with the tasks assigned to them in the field of state metrological supervision, perform the following functions:

develop and approve work plans for state metrological supervision in the Union Republic;

ensure the organization and conduct of work on state metrological supervision in the Union Republic, the continuous improvement and increase in the efficiency of state metrological supervision;

organize the conduct of state control tests of measuring instruments manufactured in the republic, state metrological certification and state verification of measuring instruments, as well as registration of enterprises manufacturing, repairing and verifying measuring instruments;

organize selective inspections of compliance with metrological rules in ministries (departments) and at enterprises located on the territory of the Union Republic;

ensure the timely adoption by the state supervision bodies of the union republic of the necessary measures to introduce and comply with metrological rules, improve the condition and use of measuring instruments, prevent and suppress violations, as well as bring to the established responsibility enterprises and officials guilty of violating metrological rules;

hear reports from the heads of republican ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

ensure the interaction of state supervision bodies with law enforcement and other regulatory bodies of the Union Republic;

exercise control over the activities of state supervision bodies in the Union Republic.

develop and approve, in accordance with the state standardization plan and on the basis of plans approved by the republican department of the State Standard, work plans for state metrological supervision at enterprises in the assigned territory, ensure an increase in the efficiency of state supervision;

carry out selective checks of compliance with metrological rules at the enterprises of the assigned territory;

organize and conduct state control tests of measuring instruments manufactured by enterprises located in the assigned territory, state metrological certification and state verification of measuring instruments, register enterprises manufacturing, repairing and verifying measuring instruments;

apply the necessary measures aimed at the implementation and observance of metrological rules, improvement of the condition and use of measuring instruments, prevention and suppression of detected violations, as well as measures to bring to the established responsibility enterprises and officials guilty of violating metrological rules;

interact with law enforcement and other regulatory authorities in the assigned territory.

2.6. The implementation of the functions of state metrological supervision is assigned to specialized structural units for supervision of the state of measuring instruments, for state testing of measuring instruments, for supervision of metrological support, as well as other units formed in the central office of the State Standard, departments of the State Standard in the Union republics, centers of standardization and metrology, laboratories of state supervision of standards and measuring equipment in autonomous republics, territories, regions and cities.

The performance of certain functions in the field of state metrological supervision is assigned to metrological research and production associations and research institutes.

2.7. Officials of the Gosstandart bodies exercising state metrological supervision and acting state inspectors for the supervision of standards and measuring instruments must be certified as a state verifier or state controller.

Certification as a state verifier is subject to persons who are entrusted with the duties of state verification of measuring instruments. These persons must undergo primary certification when they are appointed to a position, and at certain intervals - periodic certification.

Certification as a state controller (primary or periodic) is subject to persons who are assigned functions in the field of state metrological supervision in accordance with (except for verification).

Primary and periodic certification of officials exercising state supervision is carried out in the manner established by the State Standard.

3. BODIES AND SERVICES CARRYING OUT DEPARTMENTAL METROLOGICAL CONTROL.

3.1. Departmental metrological control is carried out by:

the ministry (department) by assigning these functions to the department (service) of the chief metrologist of the ministry (department);

the head and basic organizations of the metrological service of the ministry (department) with the assignment of these functions to the relevant specialized unit;

department of the chief metrologist or other structural divisions of the metrological service of enterprises that exercise control within the enterprise.

If it is not advisable to form specialized subdivisions of the metrological service in the central office of the ministry (department) or at enterprises, the functions of departmental or intra-factory control should be assigned to another structural unit or responsible person appointed by order of the ministry (department) or enterprise.

3.2.1. The ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

ensures the organization and conduct of metrological control in the system of the ministry (department), systematically checks the condition and use of measuring instruments at subordinate enterprises, takes measures aimed at strict observance of the existing metrological rules;

develops and approves, in accordance with the established procedure, sectoral work plans for departmental metrological control;

approves industry standards, instructions, rules, regulations and other NTDs that are mandatory for enterprises of its system, establishing the procedure for the implementation of departmental metrological control.

3.2.2. The department (service) of the chief metrologist of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides and exercises control over the development, production, condition, use and repair of measuring instruments, over the timely implementation and compliance with the metrological rules established by the current legislation, standards, instructions, rules, regulations and other regulatory and technical documents in the system of the ministry (department);

checks compliance with the requirements for departmental verification and metrological certification of measuring instruments in the system of the ministry (department);

exercises control over the timely submission by enterprises of the system of the ministry (department) of measuring instruments for state testing and state verification;

controls the work of the head and basic organizations of the metrological service, structural subdivisions of the metrological service at the enterprises of the system of the ministry (department);

gives mandatory for enterprises of the system of the ministry (department) instructions on the status and application of measuring instruments, implementation and compliance with metrological rules;

makes proposals to the leadership of the ministry (department) on the abolition of NTD that does not meet the requirements of state and industry standards, other NTD operating in the industry;

submits proposals to the leadership of the ministry, (department) to stop the production of products at enterprises in case of violation of metrological rules, non-compliance with which led to the release of non-standard products, until the violations are eliminated and on the need to take other measures in relation to enterprises and persons who committed these violations;

exercises control over the development and implementation of measures to eliminate the shortcomings noted by the state supervision bodies.

3.2.3. The head organization of the metrological service of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides methodological guidance to the basic organizations of the metrological service of the ministry (department) on issues of departmental metrological control;

exercises control over the activities of the basic organizations of the metrological service, as well as the activities of the metrological services of enterprises of the system of the ministry (department);

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and observance of metrological rules at enterprises of the ministry (department) system;

organizes and conducts departmental verification and metrological 1 certification of measuring instruments that cannot be verified or certified by the basic organizations of the metrological service;

makes proposals to the chief metrologist of the ministry (department) on the abolition of the NTD, orders, orders and instructions adopted in the industry, which contradict the current legislation, state and industry standards;

exercises control over the elimination of shortcomings identified by the bodies of the State Standard at the enterprises of the ministry (department) in the course of their implementation of state metrological supervision;

gives the heads of inspected enterprises mandatory instructions to eliminate the identified violations and to seize measuring instruments that are unsuitable for use;

makes proposals to the chief metrologist of the ministry (department) and heads of enterprises of the system of the ministry (department) on the need to take action against enterprises or persons that have committed violations of metrological rules.

3.2.4. The basic organization of the metrological service of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides methodological guidance to the metrological services of enterprises on issues of departmental metrological control;

controls the activities of metrological services of enterprises;

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and compliance with metrological rules at enterprises;

ensures the organization and conduct of departmental verification and metrological certification of measuring instruments that cannot be verified or certified by enterprises;

makes proposals to higher authorities on the abolition of standards adopted by the heads of enterprises and other scientific and technical documentation, orders, orders and instructions that are contrary to current legislation, state and industry standards;

renders assistance to the bodies of the State Standard in the implementation of state metrological supervision;

gives the heads of the inspected enterprises mandatory instructions on the elimination of identified violations and the seizure of measuring instruments that are unsuitable for use;

makes proposals to higher authorities and heads of attached enterprises on the need to take measures in accordance with the established procedure in relation to enterprises and persons who have committed violations of the metrological rules.

3.2.5. Head of the enterprise:

organizes and exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and observance of metrological rules, activities of structural divisions of the metrological service of the enterprise;

renders assistance to the Gosstandart bodies in their implementation of state metrological supervision;

approves the NTD, establishing the procedure for the implementation of metrological control, at the enterprise;

encourages distinguished employees, applies penalties in accordance with the established procedure against persons who have committed violations of metrological rules.

3.2.6. Department of the chief metrologist or other divisions of the metrological service of the enterprise:

exercise control over the development, production, condition and use of measuring instruments, timely implementation and observance of metrological rules by all divisions of the enterprise;

carry out departmental verification and metrological certification of measuring instruments within the rights granted by the bodies of the State Standard; keep records of the measuring instruments of the enterprise, draw up verification schedules and monitor compliance with the approved schedules; coordinate with the State Standard bodies the schedules for verification of measuring instruments subject to mandatory state verification, and ensure their timely submission for state verification; develop and implement measures for the development of departmental verification of measuring instruments;

provide assistance to the Gosstandart bodies in their implementation of state metrological supervision;

develop measures to eliminate the shortcomings identified by the bodies of the State Standard and exercise control over their implementation;

give the heads of all divisions of the enterprise mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

make proposals to the management of the enterprise on encouraging distinguished employees and on the need to take action against persons who have committed violations of metrological rules.

3.2.7. By order of the ministry (department) or enterprise, in accordance with the specific features of production, bodies and services exercising departmental metrological control may be assigned additional responsibilities in the field of monitoring compliance with metrological rules and they may be granted broader rights to apply legal measures to violators .

3.2.8. The heads of ministries (departments) and enterprises are responsible for the organization and implementation of departmental metrological control.

4. LEGAL MEASURES APPLIED IN THE ORDER OF STATE METROLOGICAL SUPERVISION.

4.2.1. Negative results of state acceptance tests of a prototype of a new type of measuring instruments are the basis for refusing to approve this type and issuing a permit for the production and release into circulation of measuring instruments of an installation series.

4.2.2. The sale of mass-produced measuring instruments that have not passed state tests in accordance with GOST 8.001-80 is the basis for the application of economic sanctions in the form of transferring the entire amount of profit received by the enterprise for this product to the budget and excluding these products in physical value terms from the reporting data of enterprises on the implementation plan.

4.2.3. Negative results of state control tests of measuring instruments are the basis for:

a) a ban (delay) in the release of the circulation of manufactured measuring instruments;

b) application of economic sanctions;

c) deprivation of the right to serial production of measuring instruments and cancellation of the registration certificate for the right to carry out these works.

4.3. When carrying out metrological certification of measuring instruments.

4.3.1. Negative results of metrological certification of newly developed measuring instruments that are not intended for mass production are the basis for a ban (suspension) of their use.

4.3.2. The implementation of newly developed measuring instruments that have not passed metrological certification is the basis for the application of economic sanctions.

4.3.3. Negative results of metrological certification of operated measuring instruments are the basis for prohibition of their use and cancellation of the certificate of metrological certification.

4.4. When conducting state verification of measuring instruments.

4.4.1. Negative results of the state verification of measuring instruments are the basis for:

a) a ban (delay) in the use or release into circulation of measuring instruments, an order to withdraw measuring instruments from circulation and operation, and, if necessary, their immediate withdrawal;

b) cancellation of impressions of verification marks on measuring instruments, cancellation of a verification certificate or a record of the unsuitability of measuring instruments in the technical passport of measuring instruments;

c) sealing the measuring instruments in a way that excludes the possibility of their further use;

d) the appointment of a continuous one-time verification of all: measuring instruments in operation, or a certain range of them in the state supervision bodies;

e) establishment of reduced calibration intervals for measuring instruments in operation.

4.5.1. Violation of the requirements established by standards and other RTDs for the manufacture, repair and verification of measuring instruments is the basis for:

a) refusal to issue a registration certificate for the right to perform the specified work;

b) instructions to stop these works and cancel the previously issued registration certificate;

c) exclusion from the registration certificate of those types of work for which violations were committed.

4.6. When checking the condition and use of measuring instruments, the activities of departmental metrological services in ministries (departments) and enterprises, the implementation and observance of metrological rules, the identified violations are the basis for the application of legal measures provided for -.

(Changed edition, Rev. No. 1).

4.7. Particularly serious violations of the metrological rules, resulting in the release of non-standard low-quality products, are the basis for mandatory instructions to company officials to stop production until the violations are eliminated.

4.8. In cases where violations of the metrological rules are the result of non-fulfillment or improper fulfillment by officials of the enterprises being inspected of their official duties, state supervision bodies have the right to submit proposals to the relevant ministries (departments) and submit proposals to the heads of enterprises on bringing these persons to disciplinary responsibility, up to and including dismissal in accordance with the established procedure from their positions.

4.9. When violations of the metrological rules are revealed, which, in accordance with the current legislation, are the basis for bringing the guilty officials to administrative responsibility in the form of a warning or a fine, the state supervision bodies draw up a protocol in the prescribed manner and send materials to the administrative commissions under the executive committees of regional, city and city district Councils of People's deputies.

4.10. In cases where the violations committed through the fault of officials by their nature entail criminal liability in accordance with the current legislation, the state supervision bodies send the materials of inspections to the investigating authorities in the prescribed manner.

4.11. The decision on the choice of legal measures corresponding to the violations of the metrological rules is taken by the officials of the state supervision bodies within the powers granted by the Chairman of the State Standard.

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR State Committee for Standards.

PERFORMERS

X. O. Malikova(topic leader) A. V. Plotnikova, V. A. Skovorodnikov, M.G. Sharonov.

2. APPROVED AND INTRODUCED BY Decree of the State Committee of the USSR on Standards dated February 21, 1986 No. 388

3. INSTEAD OF GOST 8.002-71 in part of Sec. 1, 2, 4

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS

	Number of paragraph, subparagraph, enumeration, application
GOST 8.001-80
GOST 8.326-78	1.3, 1.4
GOST 8.383-80
GOST 8.513-84	1.3, 1.4

5. Reissue (November 1987) with Amendment No. 1 approved in September 1987 (IUS 1-88).

STATE STANDARD OF THE UNION OF THE SSR

STATE SYSTEM FOR ENSURING THE UNIFORMITY OF MEASUREMENTS

STATE SUPERVISION AND DEPARTMENTAL CONTROL OVER MEASURING INSTRUMENTS

MAIN PROVISIONS

GOST 8.002-86

USSR STATE COMMITTEE ON STANDARDS

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Introduction date 01.01.87

This standard establishes the main provisions of state supervision and departmental control over the development, production, condition, use and repair of measuring instruments, over the activities of departmental metrological services, over the implementation and observance of metrological rules, including the rules for metrological support of work performed in all sectors of the national economy .

The standard does not apply to measuring instruments used at enterprises and organizations of the Ministry of Defense and manufactured by its orders.

1. GENERAL PROVISIONS.

1.1. State supervision and departmental control over measuring instruments (state metrological supervision and departmental metrological control) are carried out in order to ensure the uniformity of measurements as a necessary condition for increasing the efficiency of social production, accelerating scientific and technological progress, increasing labor productivity, improving the technical level and quality of products, ensuring reliable accounting for material, raw materials and fuel and energy resources, improving management efficiency in the sectors of the national economy.

1.2. The main task of state metrological supervision and departmental metrological control is to strengthen state discipline and increase the responsibility of ministries (departments), enterprises, associations, organizations and institutions (hereinafter referred to as enterprises) for the timely implementation and strict observance of metrological rules established by current legislation, standards, instructions, rules, regulations and other normative and technical documents, for ensuring the uniformity of measurements and metrological support of work performed in the sectors of the national economy.

state acceptance and control tests of measuring instruments in accordance with GOST 8.383-80 and GOST 8.001-80;

state metrological certification of measuring instruments in accordance with GOST 8.326-78;

state verification of measuring instruments in accordance with GOST 8.513-84;

checks of the state and application of the means of intentions, the activities of departmental metrological services in ministries (departments) and enterprises, the implementation and compliance with metrological rules (hereinafter referred to as verifications of compliance with metrological rules) in accordance with the procedure established by the State Standard.

1.4. Departmental metrological control is carried out in the form of:

departmental metrological certification of measuring instruments in accordance with GOST 8.326-78;

departmental verification of measuring instruments in accordance with GOST 8.513-84;

checks of the condition and application of measuring instruments, implementation and compliance with metrological rules at enterprises of the ministry (department) system;

inspections of the activities of the head and basic organizations of the metrological service, structural divisions of the metrological service at enterprises of the system of the ministry (department) in the manner established by the ministry (department);

certification of testing and analytical laboratories at enterprises of the ministry (department) system.

Normative and technical documents of the ministry (department) may establish other forms of departmental metrological control.

1.3, 1.4. (Revised edition, Rev. No. 1).

1.6. The organization and procedure for carrying out work on departmental metrological control is established by industry standards, rules, instructions and other NTDs of ministries (departments) and enterprises that must comply with the requirements of this standard, other state standards and NTD Gosstandart regulating issues of state metrological supervision and departmental metrological control.

2. BODIES CARRYING OUT STATE METROLOGICAL SUPERVISION.

2.1. State metrological supervision is carried out by:

Gosstandart;

republican departments of Gosstandart in the union republics;

centers for standardization and metrology, laboratories for state supervision of standards and measuring equipment of the State Standard.

2.2. State supervision bodies carry out their functions in accordance with the established competence.

2.3. Gosstandart, in accordance with the tasks assigned to it in the field of state metrological supervision, performs the following functions:

approves standards and other scientific and technical documentation, mandatory for use by all ministries, departments, enterprises;

develops and approves, in accordance with the established procedure, work plans for state metrological supervision;

hears at meetings of the State Standard reports of the heads of ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

analyzes the results of state metrological supervision and develops measures to eliminate the identified shortcomings;

manages the activities of state supervision bodies of the Gosstandart system.

2.4. Republican departments of the State Standard, in accordance with the tasks assigned to them in the field of state metrological supervision, perform the following functions:

develop and approve work plans for state metrological supervision in the Union Republic;

ensure the organization and conduct of work on state metrological supervision in the Union Republic, the constant improvement and increase in the efficiency of state metrological supervision;

organize selective inspections of compliance with metrological rules in ministries (departments) and at enterprises located on the territory of the Union Republic;

hear reports from the heads of republican ministries (departments) on the state of affairs at subordinate enterprises based on the results of state metrological supervision;

ensure the interaction of state supervision bodies with law enforcement and other regulatory bodies of the Union Republic;

exercise control over the activities of state supervision bodies in the Union Republic.

develop and approve, in accordance with the state standardization plan and on the basis of plans approved by the republican department of the State Standard, work plans for state metrological supervision at enterprises of the assigned territory, ensure an increase in the efficiency of state supervision;

carry out selective checks of compliance with metrological rules at the enterprises of the assigned territory;

apply the necessary measures aimed at the implementation and observance of metrological rules, improvement of the condition and use of measuring instruments, prevention and suppression of identified violations, as well as measures to bring to the established responsibility enterprises and officials guilty of violating metrological rules;

interact with law enforcement and other regulatory authorities in the assigned territory.

2.6. The implementation of the functions of state metrological supervision is assigned to specialized structural units for supervision of the state of measuring instruments, for state testing of measuring instruments, for supervision of metrological support, as well as to other units formed in the central office of Gosstandart, Gosstandart departments in the Union republics, standardization centers and metrology, laboratories of state supervision of standards and measuring equipment in autonomous republics, territories, regions and cities.

The performance of certain functions in the field of state metrological supervision is assigned to metrological research and production associations and research institutes.

Certification as a state controller (primary or periodic) is subject to persons who are assigned functions in the field of state metrological supervision in accordance with (except for verification).

Primary and periodic certification of officials exercising state supervision is carried out in the manner established by the State Standard.

3. BODIES AND SERVICES CARRYING OUT DEPARTMENTAL METROLOGICAL CONTROL.

3.1. Departmental metrological control is carried out by:

the ministry (department) with the assignment of these functions to the department (service) of the chief metrologist of the ministry (department);

the head and basic organizations of the metrological service of the ministry (department) with the assignment of these functions to the appropriate specialized unit;

department of the chief metrologist or other structural divisions of the metrological service of enterprises exercising control within the enterprise.

If it is not advisable to form specialized subdivisions of the metrological service in the central office of the ministry (department) or at enterprises, the functions of departmental or in-plant control should be assigned to another structural unit or responsible person appointed by order of the ministry (department) or enterprise.

3.2.1. The ministry (department), in accordance with the tasks assigned to it in the field of departmental metrological control:

develops and approves, in accordance with the established procedure, sectoral work plans for departmental metrological control;

approves industry standards, instructions, rules, regulations and other scientific and technical documentation that are mandatory for enterprises of its system, establishing the procedure for implementing departmental metrological control.

3.2.2. The department (service) of the chief metrologist of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides and carries out in the system of the ministry (department) control over the development, production, condition, use and repair of measuring instruments, over the timely implementation and observance of the metrological rules established by the current legislation, standards, instructions, rules, regulations and other regulatory and technical documents;

checks compliance with the requirements for departmental verification and metrological certification of measuring instruments in the system of the ministry (department);

exercises control over the timely submission by enterprises of the system of the ministry (department) of measuring instruments for state testing and state verification;

controls the work of the head and basic organizations of the metrological service, structural subdivisions of the metrological service at the enterprises of the system of the ministry (department);

gives mandatory for enterprises of the system of the ministry (department) instructions on the status and application of measuring instruments, implementation and compliance with metrological rules;

makes proposals to the leadership of the ministry (department) on the abolition of scientific and technical documentation that does not meet the requirements of state and industry standards, other scientific and technical documentation operating in the industry;

makes proposals to the leadership of the ministry, (department) on the termination of production at enterprises in case of violation of metrological rules, non-compliance with which led to the production of non-standard products, until the violations are eliminated and on the need to take other measures in relation to enterprises and persons who have committed these violations;

exercises control over the development and implementation of measures to eliminate the shortcomings noted by the state supervision bodies.

3.2.3. The head organization of the metrological service of the ministry (department), in accordance with the tasks assigned to it in the field, departmental metrological control:

provides methodological guidance to the basic organizations of the metrological service of the ministry (department) on issues of departmental metrological control;

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and compliance with metrological rules at enterprises of the ministry (department) system;

organizes and conducts departmental verification and metrological 1 certification of measuring instruments that cannot be verified or certified by the basic organizations of the metrological service;

makes proposals to the chief metrologist of the ministry (department) on the abolition of scientific and technical documentation adopted in the industry, orders, orders and instructions that contradict the current legislation, state and industry standards;

exercises control over the elimination of shortcomings identified by the Gosstandart bodies at the enterprises of the ministry (department) when they exercise state metrological supervision;

gives the heads of inspected enterprises mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

makes proposals to the chief metrologist of the ministry (department) and heads of enterprises of the system of the ministry (department) on the need to take measures against enterprises and persons who have committed violations of metrological rules.

3.2.4. The basic organization of the metrological service of the ministry (department) in accordance with the tasks assigned to it in the field of departmental metrological control:

provides methodological guidance to the metrological services of enterprises on issues of departmental metrological control;

controls the activities of metrological services of enterprises;

exercises control over the development, production, condition, use and repair of measuring instruments, timely implementation and compliance with metrological rules at enterprises;

ensures the organization and conduct of departmental verification and metrological certification of measuring instruments that cannot be verified or certified by enterprises;

makes proposals to higher authorities on the abolition of standards and other scientific and technical documentation adopted by the heads of enterprises, orders, orders and instructions that are contrary to current legislation, state and industry standards;

renders assistance to the bodies of the State Standard in the implementation of state metrological supervision;

gives the heads of inspected enterprises mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

makes proposals to higher authorities and heads of attached enterprises on the need to take measures in the prescribed manner in relation to enterprises and persons who have committed violations of metrological rules.

3.2.5. Head of the enterprise:

renders assistance to Gosstandart bodies in their implementation of state metrological supervision;

approves the NTD, establishing the procedure for the implementation of metrological control, at the enterprise;

encourages distinguished employees, applies penalties in accordance with the established procedure against persons who have committed violations of metrological rules.

3.2.6. Department of the chief metrologist or other divisions of the metrological service of the enterprise:

exercise control over the development, production, condition and use of measuring instruments, timely implementation and compliance with metrological rules by all divisions of the enterprise;

carry out departmental verification and metrological certification of measuring instruments within the rights granted by the Gosstandart bodies; keep records of the measuring instruments of the enterprise, draw up calibration schedules and monitor compliance with the approved schedules; coordinate with the State Standard bodies the schedules for verification of measuring instruments subject to mandatory state verification, and ensure their timely submission for state verification; develop and implement measures for the development of departmental verification of measuring instruments;

provide assistance to the Gosstandart bodies in their implementation of state metrological supervision;

develop measures to eliminate the shortcomings identified by the bodies of the State Standard and exercise control over their implementation;

give the heads of all departments of the enterprise mandatory instructions to eliminate the identified violations and to withdraw measuring instruments that are unsuitable for use;

make proposals to the management of the enterprise on encouraging distinguished employees and on the need to take action against persons who have committed violations of metrological rules.

3.2.8. The heads of ministries (departments) and enterprises are responsible for the organization and implementation of departmental metrological control.

4. LEGAL MEASURES USED UNDER THE ORDER OF STATE METROLOGICAL SUPERVISION.

4.2.2. The sale of mass-produced measuring instruments that have not passed state tests in accordance with GOST 8.001-80 is the basis for the application of economic sanctions in the form of transferring the entire amount of profit received by the enterprise for these products to the budget and excluding these products in kind and value terms from reporting data of enterprises on the implementation of the plan.