Stages of design development GOST 2.103. Terms and Definitions
page 1
page 2
page 3
page 4
page 5
page 6
page 7
page 8
page 9
page 10
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE
STANDARD
GOST 2.103-2013
2013
Unified system of design documentation STAGES OF DEVELOPMENT
Official edition
|
Standartinform ForewordThe goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic Provisions” and GOST 1.2-2009 “Interstate Standardization System. Interstate standards, rules and recommendations for interstate standardization. Rules for the development, adoption, application, updating and cancellation " About the standard 1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute for Standardization and Certification in Mechanical Engineering" (VNIINMASH), Autonomous non-profit organization Research Center for CALS-technologies "Applied Logistics" (ANO NRC CALS-technologies "Applied Logistics") 2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology 3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes of November 14, 2013 No. 44, Appendix No. 24 add.)
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 26, 2014 No. 1794-st, the interstate standard GOST 2.103-2013 was put into effect as the national standard of the Russian Federation from July 01, 2015. 6 SECOND EDITION (April 2015) as amended in IUS No. 7 2015. Information about changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments - in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notification and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet © Standartinform, 2015 In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology |
||||||||||||||||||||||||||||||||||||
|
(IUS No. 7 2015) |
|
|||||||||
|
(IUS No. 10 2016) |
3.1.1 one-off manufacturing
|
End of table 1 |
|||||||||||||||||||||||||
|
|||||||||||||||||||||||||
4.2 The nomenclature of the types of documents developed at each stage of development of the design documentation - according to GOST 2.102, if the composition of the documentation is not established in the TOR for development.
4.3 The obligatory fulfillment of the development stages and stages of work, the form of presentation of the design documentation (paper and (or) electronic) must be established by the developer, if this is not specified in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages in progress.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop mock-ups, their type, conditions and test (analysis) programs, as well as the need to develop documentation for the manufacture and testing of mock-ups, should be established by the developer, if this is not specified in the TOR for development. Models can be made in material form (material model) or virtual form (electronic model). Requirements for a material layout in accordance with GOST 2.002, for an electronic layout - in accordance with GOST 2.052.
Material layouts should be made, as a rule, according to draft design documentation, in accordance with GOST 2.125 * 1 '.
4.7 When performing electronic design documents, it is recommended that the requirements for data formats be set at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic design documentation, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a level of detail corresponding to the development stage. Requirements for the electronic model of the product - according to GOST 2.052, for the electronic structure of the product - according to GOST 2.053.
4.9 Working design documentation for single-piece production products may be preceded by the execution of design documentation of individual development stages (technical proposal, draft design, technical design) and, accordingly, the stages of work specified in table 1.
4.10 Technical proposal - a set of project design documentation that should contain technical and feasibility studies on the feasibility of developing product documentation based on the analysis of the technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research .
The technical proposal, after being agreed and approved in the prescribed manner, is the basis for the development of a preliminary (technical) design.
4.11 Draft design - a set of design design documentation that should contain fundamental design solutions that give a general idea of the purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a technical design or working design documentation.
4.12 Technical design - a set of design design documentation, which should contain the final technical solutions that give a complete picture of the design of the product being developed, and the initial data for the development of the working design documentation.
The technical design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a working design documentation.
4.13 Previously developed design documentation should be used when developing new or upgrading manufactured products in the following cases:
a) in the design design documentation (technical proposal, draft and technical designs);
b) in the working CD with the letters “O”, “O ^ (“0 2”, “O e”, ... “O p”), “A”, “B” and “I”, if the lettering of the document used the same or higher.
The lettering of a complete set of design documentation is determined by the lowest of the letters indicated in the design documentation included in the set, except for the design documentation of purchased products.
4.14 CDs, the original holders of which are other organizations, can be used in the organization only if there are registered copies or duplicates of these CDs.
4.15 At the development stages, the "Development of the design DD" should be developed for the design
At the stages "Development of a working DD", a working DD should be developed.
The working design documentation transferred (delivered) to the manufacturer for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601, which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle " Design (development)”.
Repair design documentation, if necessary, should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain period of operation of the product *.
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION
INTERSTATE
STANDARD
Official edition
Standartinform
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic Provisions” and GOST 1.2-2009 “Interstate Standardization System. Interstate standards, rules and recommendations for interstate standardization. Rules for the development, adoption, application, updating and cancellation "
About the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute for Standardization and Certification in Mechanical Engineering" (VNIINMASH), Autonomous non-profit organization Research Center for CALS-technologies "Applied Logistics" (ANO NRC CALS-technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (minutes of November 14, 2013 Nv 44, Appendix Ns> 24 add.)
| Short country name no MK (ISO 3166) 004-97 |
Country code according to MK (ISO 3166) 004-97 |
Abbreviated name of the national standards body |
| Azerbaijan |
Azstandard |
|
| Ministry of Economy of the Republic of Armenia |
||
| Belarus |
State Standard of the Republic of Belarus |
|
| Kazakhstan |
State Standard of the Republic of Kazakhstan |
|
| Kyrgyzstan |
Kyrgyzstandart |
|
| Moldova-Standard |
||
| Rosstandart |
||
| Tajikistan |
Tajikstandart |
|
| Uzbekistan |
Uzstandard |
|
| State Consumer Standard of Ukraine |
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 26, 2014 No. 1794-st, the interstate standard GOST 2.103-2013 was put into effect as the national standard of the Russian Federation from July 01, 2015.
6 SECOND EDITION (April 2015) as amended in IUS No. 7 2015.
Information about changes to this standard is published in the annual information index "National Standards". and the text of changes and amendments - in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notification and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet
© Standartinform, 2015
In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology
INTERSTATE
GOST 2.103-2013
STANDARD
Unified system of design documentation DEVELOPMENT STAGES
Unified system for design documentation Stages of design
Introduction date - 2015-07-01
1 area of use
This standard establishes the stages of development of design documentation for products of all industries and the stages of work.
On the basis of this standard, standards can be developed that take into account the features of the application of the stages of development of design documentation at various stages of the life cycle of a product of specific types of equipment, depending on the specifics of their development, production and use.
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in the design
GOST 2.052-2006 Unified system for design documentation. Electronic product model. General provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-203. Unified system of design documentation. Technical proposal GOST 2.119-2013 Unified system for design documentation. Draft design GOST 2.120-2013 Unified system for design documentation. Technical project GOST 2.125-2008 Unified system for design documentation. Rules for the implementation of draft design documents. General provisions
GOST 2.601-2013 Unified system for design documentation. Operating documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and on issues of the monthly information index "National Standards" for the current year. If the reference standard is replaced (modified), then when using this standard, you should be guided by the replacing (modified) standard. If the referenced standard is canceled without replacement, the provision in which the reference to it is given applies to the extent that this reference is not affected.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
In this standard, the following terms are used with their respective definitions:
Official edition
3.1.1 one-off manufacturing
__[GOST 14.004-83. paragraph 20]
3.1.2 letter: Detail of the design document (set of design documents) on
product corresponding to the stage of its development._
3.1.3 prototype: A product sample manufactured according to the newly developed working documentation for verification by testing its compliance with specified technical requirements in order to make a decision on the possibility of putting into production and (or) use for its intended purpose.
_[GOST 16504-81, art. 8]
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products manufactured over a specified time interval according to the newly developed one and the same documentation to control product compliance with specified requirements and make a decision on putting it into production.
3.1.5 project design documentation: Design documentation,
performed at the stages of a technical proposal, draft and technical designs.
3.1.6 working design documentation: design documentation made at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 stage of development of design documentation: The completed part of the process of development of design documentation, consisting of stages of work performance and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured in the period
development of production according to the documentation of serial or mass production in order to confirm the readiness of production for the release of products with established requirements and in specified volumes._
3.1.9 data format: An arrangement of data symbols that makes it possible to recognize their component parts.
NOTE The format of the data takes on a variation depending on the particular set of data symbols, eg the format of the data message.
[GOST 17657-79. Annex, paragraph 11]
3.2 Abbreviations
The following abbreviations are used in this standard:
CD - design documents (documents, documentation);
TK - technical task.
4 Fundamentals
4.1 The stages of development of design documentation can be carried out in the form of development of design and working design documentation.
The stages of development of design documentation and the stages of work performance established by this standard are shown in Table 1.
Table 1
| Development stage |
Stages of work |
|
| Development of design documentation |
Development of a technical proposal *" |
Study and analysis of TK |
| Selection of materials |
||
| Development of design documentation for a technical proposal. |
||
| Consideration and approval of the DD of the technical proposal with the assignment of the DD of the letter VP " |
||
| Development of a draft design |
Development of a draft design |
|
| Production and testing and / or development and analysis of material models (if necessary) and (or) development, analysis of electronic models (if necessary) |
||
| Consideration and approval of the design documentation of the preliminary design with the assignment of the letter "E" to the documents |
||
GOST 2.103-2013
End of table 1
| Development stage |
Stages of work |
|
| Development design |
Development of a technical project |
|
| Production and testing of material models (if necessary) and / or development, analysis of electronic models (if necessary) |
||
| Consideration and approval of the design documentation of the technical project with the assignment of the design documentation of the letter * T " |
||
| Development |
Development of design documentation for a prototype (pilot batch) of a product |
Development of CD. intended for the manufacture and testing of a prototype (pilot batch) of a product, without assigning a letter |
| Manufacturing and preliminary testing of a prototype (pilot batch) of the product |
||
| Correction of the design documentation based on the results of manufacturing and preliminary testing of a prototype (pilot batch) of the product with the assignment of the design documentation of the letter "O" |
||
| Acceptance testing of a prototype (pilot batch) of a product |
||
| Correction of the design documentation based on the results of acceptance tests of a prototype (pilot batch) of the product with the assignment of the design documentation of the letter "Oi" |
||
| For a product developed by order of the Ministry of Defense, if necessary, re-production and testing of a prototype (pilot batch) according to the documentation with the letter “Oi” and adjustment of the design documentation with the assignment of the letter “Og *” to them. "Oz". ...«0„* |
||
| Development of design documentation for a serial (mass) production product |
Production and testing of the installation series according to the documentation with the letter "Oi" (or "Og". "Oj", ... "O p") |
|
| Correction of the design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process for manufacturing the product, with the assignment of the design documentation of the letter "A" |
||
| For a product developed by order of the Ministry of Defense, if necessary, the manufacture and testing of the lead (control) series according to the design documentation with the letter "A" and the corresponding adjustment of the design documentation with the assignment of the letter "B" to them |
||
| Development of design documentation for a single-piece production product |
Development of CD. intended for the manufacture and testing of products with the assignment of the letter "I" to them |
|
| ” The “Technical Proposal” stage does not apply to the design documentation. developed by order of the Ministry of Defense. Note - All stages of the development of the working design documentation may be preceded by the stage of development of the design design documentation. |
||
4.2 The nomenclature of the types of documents developed at each stage of the development of a design documentation - according to GOST 2.102. if the composition of the documentation is not set in the TOR for development.
4.3 The obligatory fulfillment of the development stages and stages of work, the form of presentation of the design documentation (paper and (or) electronic) must be established by the developer, if this is not specified in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages in progress.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop layouts, their appearance. the conditions and test programs (analysis), as well as the need to develop documentation for the manufacture and testing of mock-ups, should be established by the developer, if this is not specified in the TOR for development. Models can be made in material form (material model) or virtual form (electronic model). Requirements for the material layout according to GOST 2.002. to the electronic layout - according to GOST 2.052.
Material layouts should be made, as a rule, according to draft design documentation. in accordance with
4.7 When performing electronic design documents, it is recommended that the requirements for data formats be set at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic design documentation, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a level of detail corresponding to the development stage. Requirements for the electronic model of the product - according to GOST 2.052. to the electronic structure of the product - according to GOST 2.053.
4.9 Working design documentation for single-piece production products may be preceded by the execution of design documentation of individual development stages (technical proposal, draft design, technical design) and, accordingly, the stages of work specified in table 1.
4.10 Technical proposal - a set of design design documentation. which should contain technical and feasibility studies of the feasibility of developing product documentation based on the analysis of the technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research.
The technical proposal, after being agreed and approved in the prescribed manner, is the basis for the development of a preliminary (technical) design.
The list of works - according to GOST 2.118.
4.11 Draft design - a set of design design documentation. which should contain fundamental design solutions that give a general idea of the purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a technical design or working design documentation.
List of works - according to GOST 2.119.
4.12 Technical design - a set of design design documentation. which should contain the final technical solutions that give a complete picture of the design of the product being developed, and the initial data for the development of a working design documentation.
The technical design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a working design documentation.
List of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used when developing new or upgrading manufactured products in the following cases:
a) in the design design documentation (technical proposal, draft and technical designs);
b) in the working design documentation with the letters "O". “Oh,” (“Oh g”, “0 3”, ... “Oh p”), “A”, “B” and “I”, if the lettering of the document used is the same or higher.
The lettering of a complete set of DD is determined by the lowest of the letters indicated in the DD. included in the kit, except for the design documentation of purchased products.
4.14 CD. whose originals are held by other organizations, can be used in the organization only if there are registered copies or duplicates of these CDs.
4.15 At the development stages, the "Development of the design DD" should be developed for the design
At the stages "Development of a working DD", a working DD should be developed.
Working CD. transferred (supplied) to the manufacturer for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601. which is then delivered to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle "Design (development)".
Repair CD. if necessary, it should be developed in accordance with GOST 2.602 at the stage of the life cycle of the product "Repair", as a rule, after a certain period of operation of the product *.
GOST 2.103-2013
Annex A (informative)
Approved by the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR in December 1967. Date of introduction set
1971-01-01
1. This standard establishes the stages of development of design documentation for products in all industries and the stages of work at each stage of development (see table).
|
Development stage |
Stages of work |
|
Technical Proposal |
Selection of materials. Development of a technical proposal with the assignment of the letter "P" to the documents. Consideration and approval of the technical proposal |
|
Preliminary design |
Development of a preliminary design with the assignment of the letter "E" to the documents. Production and testing of material models (if necessary) and (or) development, analysis of electronic models (if necessary) Consideration and approval of the preliminary design. |
|
Technical project |
Development of a technical project with the assignment of the letter "T" to the documents. Production and testing of material material models (if necessary) and (or) development, analysis of electronic models (if necessary). Consideration and approval of the technical project. |
|
Working design documentation: a) a prototype (pilot batch) of a product intended for serial (mass) or unit production (except for one-time production) |
Development of design documentation intended for the manufacture and testing of a prototype (pilot batch), without assigning a letter. Manufacturing and preliminary testing of a prototype (pilot batch). Adjustment of design documentation based on the results of manufacturing and preliminary testing of a prototype (pilot batch) with the assignment of the letter “O” to the documents. Acceptance testing of a prototype (pilot batch). Adjustment of design documentation based on the results of acceptance tests of a prototype (pilot batch) with the assignment of the letter “O1” to the documents. For a product developed by order of the Ministry of Defense, if necessary, re-production and testing of a prototype (pilot batch) according to the documentation with the letter "O1" and adjustment of design documents with the assignment of the letter "O2" to them. |
|
b) serial (mass) production |
Production and testing of the installation series according to the documentation with the letter "O1" (or "O2"). Correction of design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process for manufacturing the product, with the assignment of the letter “A” to the design documents. For a product developed by order of the Ministry of Defense, if necessary, the manufacture and testing of the head (control) series according to the documentation with the letter "A" and the corresponding adjustment of the documents with the assignment of the letter "B" to them |
The obligatory fulfillment of the development stages and stages of work, the form of presentation of design documentation (paper or electronic) is established by the developer, if this is not provided for by the terms of reference for the development.
Notes:
1. The "Technical proposal" stage does not apply to the design documentation of products developed by order of the Ministry of Defense.
2. The layout is being developed:
a) at the stage of a technical proposal in order to identify and verify options for the main design solutions of the developed product or its components, analyze various product options, identify additional or refined requirements for the product;
b) at the stage of a preliminary design in order to check the principles of operation of the product or its components, the conditions of placement in the allotted space, the conditions for ergonomic use and other properties of the product or its components;
c) at the stage of a technical project in order to check the main design solutions of the product being developed or its components in terms of spatial and kinematic interaction with other products and components among themselves, as well as ergonomic conditions;
d) at the stage of the working design for preliminary verification of the feasibility of changing individual parts of the manufactured product before making these changes in the working design documents of the prototype (pilot batch).
Models can be made in material form (material model) or electronic form (electronic model).
3. The need to develop mock-ups, their type, conditions and test programs (analysis), as well as the need to develop documentation for the manufacture and testing of mock-ups is established by the developer. Requirements for the material layout - according to GOST 2.002-72, for the electronic layout - according to GOST 2.052-2006.
4. A one-time production is understood as a one-time production of one or more copies of a product, the further production of which is not provided.
5. When performing design documentation in electronic form, it is recommended to set the requirements for data formats at a previous stage of development, if this is not provided for in the terms of reference.
(Introduced additionally,Change No. 2 )
2. Working design documents for single-piece production products intended for one-time production are assigned the letter “I” during their development, which may be preceded by the implementation of individual development stages (technical proposal, draft design technical design) and, accordingly, the stages of work indicated in the table.
1 , 2. (Changed edition, Rev. No. 1).
3 . (Deleted, Rev. No. 1).
4. Technical proposal - a set of design documents that should contain technical and feasibility studies of the feasibility of developing product documentation based on an analysis of the customer's technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products and patent research.
The technical proposal, after being agreed and approved in the prescribed manner, is the basis for the development of a preliminary (technical) design.
(Changed edition, Rev. No. 1, 2).
5. Draft design - a set of design documents that should contain fundamental design solutions that give a general idea of the purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine the purpose, main parameters and overall dimensions of the product being developed.
The draft design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a technical project or working design documentation.
6. Technical design - a set of design documents that must contain final technical solutions that give a complete picture of the design of the product being developed, and initial data for the development of working documentation.
The technical design, after being agreed and approved in the prescribed manner, serves as the basis for the development of working design documentation.
7. Previously developed design documents are used in the development of new or modernization of manufactured products in the following cases:
a) in project documentation (technical proposal, draft and technical designs) and working documentation of a prototype (pilot batch) - regardless of the lettering of the documents used;
b) in the design documentation with the letters "O1" ("O2"), "A" and "B", if the lettering of the document used is the same or higher.
The lettering of a complete set of design documentation is determined by the lowest of the letters indicated in the documents included in the set, except for documents of purchased products.
(Revised edition, Rev. No. 1).
8. Design documents, the original holders of which are other enterprises, can only be used if there are registered copies or duplicates.
GOST 2.103-2013
INTERSTATE STANDARD
Unified system of design documentation
STAGES OF DEVELOPMENT
Unified system for design documentation Stages of design
For the text of Comparison of GOST 2.103-2013 with GOST 2.103-68, see the link.
- .
____________________________________________________________________
ISS 01.110
OKSTU 0002
Introduction date 2015-07-01
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 "Interstate standardization system. Basic provisions" and GOST 1.2-2009 "Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for the development, adoption, application, renewal and cancellation
About the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Scientific Research Institute for Standardization and Certification in Mechanical Engineering" (VNIINMASH), Autonomous non-profit organization Research Center for CALS-technologies "Applied Logistics" (ANO NRC CALS-technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes No. 44 of November 14, 2013, Appendix No. 24 add.)
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 26, 2014 N 1794-st, the interstate standard GOST 2.103-2013 was put into effect as the national standard of the Russian Federation from July 01, 2015.
5 INSTEAD OF GOST 2.103-68
6 SECOND EDITION (April 2015) as amended by IUS N 7 2015
Information about changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments - in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notification and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet
Amended by database manufacturer
1 area of use
1 area of use
This standard establishes the stages of development of design documentation for products of all industries and the stages of work.
On the basis of this standard, standards can be developed that take into account the features of the application of the stages of development of design documentation at various stages of the life cycle of a product of specific types of equipment, depending on the specifics of their development, production and use.
2 Normative references
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in the design
GOST 2.052-2006 Unified system for design documentation. Electronic product model. General provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-2013 Unified system for design documentation. Technical Proposal
GOST 2.119-2013 Unified system for design documentation. Preliminary design
GOST 2.120-2013 Unified system for design documentation. Technical project
GOST 2.125-2008 Unified system for design documentation. Rules for the implementation of draft design documents. General provisions
GOST 2.601-2013 Unified system for design documentation. Operating documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and on issues of the monthly information index "National Standards" for the current year. If the reference standard is replaced (modified), then when using this standard, you should be guided by the replacing (modified) standard. If the referenced standard is canceled without replacement, the provision in which the reference to it is given applies to the extent that this reference is not affected.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
In this standard, the following terms are used with their respective definitions:
3.1.2 letter: Details of the design document (set of design documents) for the product corresponding to the stage of its development.
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products manufactured within a specified time interval according to the newly developed one and the same documentation to control the compliance of products with specified requirements and make a decision on putting them into production.
3.1.5 project design documentation: Design documentation made at the stages of technical proposal, draft and technical projects.
3.1.6 working design documentation: Design documentation made at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 stage of development of design documentation: A completed part of the process of developing design documentation, consisting of stages of work performance and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured during the period of mastering production according to the documentation of serial or mass production in order to confirm the readiness of production for the production of products with established requirements and in specified volumes.
3.2 Abbreviations
The following abbreviations are used in this standard:
CD - design documents (documents, documentation);
TK - technical task.
4 Fundamentals
4.1 The stages of development of design documentation can be carried out in the form of development of design and working design documentation. The stages of development of design documentation and the stages of work performance established by this standard are shown in Table 1.
Table 1
Development stage | ||
The "Technical Proposal" stage does not apply to design documentation developed* by order of the Ministry of Defense. Note - All stages of the development of the working design documentation may be preceded by the stage of development of the design design documentation. |
__________
* The text of the document corresponds to the original. - .
Table 1. (Amendment. IUS N 10-2016).
4.2 The nomenclature of the types of documents developed at each stage of development of the design documentation - according to GOST 2.102, if the composition of the documentation is not established in the TOR for development.
4.3 The obligatory fulfillment of the development stages and stages of work, the form of presentation of the design documentation (paper and (or) electronic) must be established by the developer, if this is not specified in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages in progress.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop mock-ups, their type, conditions and test (analysis) programs, as well as the need to develop documentation for the manufacture and testing of mock-ups, should be established by the developer, if this is not specified in the TOR for development. Models can be made in material form (material model) or virtual form (electronic model). Requirements for the material layout according to GOST 2.002, for the electronic layout - according to GOST 2.052.
Material layouts should be made, as a rule, according to draft design documentation, in accordance with GOST 2.125 *.
_______________
Here and below, "*" marks the points to which comments are given in Appendix A.
4.7 When performing electronic design documents, it is recommended that the requirements for data formats be set at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic design documentation, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a level of detail corresponding to the development stage. Requirements for the electronic model of the product - in accordance with GOST 2.052, for the electronic structure of the product - in accordance with GOST 2.053.
4.9 Working design documentation for single-piece production products may be preceded by the execution of design documentation of individual development stages (technical proposal, draft design, technical design) and, accordingly, the stages of work specified in table 1.
4.10 Technical proposal - a set of project design documentation that should contain technical and feasibility studies on the feasibility of developing product documentation based on the analysis of the technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research .
The technical proposal, after being agreed and approved in the prescribed manner, is the basis for the development of a preliminary (technical) design.
The list of works - according to GOST 2.118.
4.11 Draft design - a set of design design documentation that should contain fundamental design solutions that give a general idea of the purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a technical design or working design documentation.
The list of works - according to GOST 2.119.
4.12 Technical design - a set of design design documentation, which should contain the final technical solutions that give a complete picture of the design of the product being developed, and the initial data for the development of the working design documentation.
The technical design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a working design documentation.
The list of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used when developing new or upgrading manufactured products in the following cases:
a) in the design design documentation (technical proposal, draft and technical designs);
b) in the working CD with the letters "", "" ("", "", ... ""), "A", "B" and "I", if the lettering of the document used is the same or higher.
The lettering of a complete set of design documentation is determined by the lowest of the letters indicated in the design documentation included in the set, except for the design documentation of purchased products.
4.14 CDs, the original holders of which are other organizations, can be used in the organization only if there are registered copies or duplicates of these CDs.
4.15 At the development stages, "Development of the design DD" should be developed for the design DD.
At the stages of "Development of a working DD", a working DD should be developed.
The working design documentation transferred (supplied) by the manufacturer for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601, which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the "Design (development)" stage of the product life cycle.
Repair design documentation, if necessary, should be developed in accordance with GOST 2.602 at the stage of the life cycle of the product "Repair", as a rule, after a certain period of operation of the product *.
Annex A (informative). Comments on paragraphs of the standard
Annex A
(reference)
4.6 An electronic layout is a set of electronic models of a product that describes its external shape and dimensions, allowing to fully or partially evaluate its interaction with elements of the production and / or operational environment, which serves to make a decision when developing a product and processes for its manufacture and use.
An electronic model is a virtual image of a product or a simulation of the specific properties of a product being created or its component, which allows you to fully or partially explore the individual characteristics of the product, as well as evaluate the correctness of the adopted technical and design solutions.
Material and electronic layouts should be developed:
a) at the stage of developing a technical proposal in order to identify and test options for the main design solutions of the product being developed or its components, analyze various product options, identify additional or refined requirements for the product;
b) at the stage of developing a draft design in order to check the principles of operation of the product or its components, the conditions for placement in the allotted space, the conditions for ergonomic use and other properties of the product or its components;
c) at the stage of development of a technical project in order to check the main design solutions of the developed product or its components in terms of spatial-kinematic interaction with other products and components among themselves and ergonomic conditions;
d) at the stage of developing a working design documentation for a preliminary check of the feasibility of changing individual components of the manufactured product before making these changes to the working design documentation of a prototype (pilot batch).
4.15 The life cycle of a product, as a rule, consists of the following stages: marketing and scientific research, design (development), manufacture, control (acceptance), operation, repair, disposal.
Electronic text of the document
and verified by:
official publication
M.: Standartinform, 2015
Revision of the document, taking into account
changes and additions prepared
STATE STANDARD OF THE UNION OF THE SSR
Unified system of design documentation
Introduction date 1971-01-01
APPROVED by the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR in December 1967
REPUBLICATION (March 1995) with Amendment No. 1 approved in July 1981 (IUS No. 10-81)
1. This standard establishes the stages of development of design documentation for products in all industries and the stages of work (see table).
The standard complies with ST SEV 208-75.
Development stage | Stages of work |
Technical Proposal | Selection of materials. |
Development of a technical proposal with the assignment of the letter "P" to the documents. |
|
Consideration and approval of the technical proposal. |
|
Preliminary design | Development of a preliminary design with the assignment of the letter "E" to documents. |
Consideration and approval of the preliminary design. |
|
Technical project | Development of a technical project with the assignment of the letter "T" to documents. |
Production and testing of layouts (if necessary). |
|
Consideration and approval of the technical project. |
|
Working design documentation: | Development of design documentation intended for the manufacture and testing of a prototype (pilot batch), without assigning a letter. |
a) a prototype (pilot batch) of a product intended | Production and preliminary testing of a prototype (pilot batch). |
for serial (mass) or single-piece production (except for one-time production) | Correction of design documentation based on the results of manufacturing and preliminary testing of a prototype (pilot batch) with the assignment of the letter "O" to the documents. |
Acceptance testing of a prototype (pilot batch). |
|
Adjustment of design documentation based on the results of acceptance tests of a prototype (pilot batch) with the assignment of the letter "" to the documents. |
|
For a product developed by order of the Ministry of Defense, if necessary, re-production and testing of a prototype (pilot batch) according to the documentation with the letter "" and adjustment of design documents with the assignment of the letter "". |
|
b) serial (mass) production | Production and testing of the installation series according to the documentation with the letter "" (or ""). |
Adjustment of the design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process for manufacturing the product, with the assignment of the letter "A" to the design documents. |
|
For a product developed by order of the Ministry of Defense, if necessary, the manufacture and testing of the head (control) series according to the documentation with the letter "A" and the corresponding adjustment of documents with the assignment of the letter "B" to them |
The obligatory fulfillment of the stages and stages of development of design documentation is established by the terms of reference for development.
Notes:
1. The "Technical proposal" stage does not apply to the design documentation of products developed by order of the Ministry of Defense.
2. The need to develop documentation for the manufacture and testing of models is established by the developer.
3. Design documentation for the manufacture of mock-ups is developed with the aim of: checking the principles of operation of the product or its components at the stage of the draft design; verification of the main design solutions of the developed product or its components at the stage of the technical design; preliminary verification of the feasibility of changing individual parts of the manufactured product before making these changes to the working design documents of a prototype (pilot batch).
4. A one-time production is understood as a one-time production of one or more copies of a product, the further production of which is not provided.
2. The working design documents of a single-piece production product intended for one-time production are assigned the letter "I" during their development, which may be preceded by the implementation of individual development stages (technical proposal, draft design, technical design) and, accordingly, the stages of work indicated in the table.
1, 2.
3. (Deleted, Rev. No. 1).
4. Technical proposal - a set of design documents that should contain technical and feasibility studies of the feasibility of developing product documentation based on an analysis of the customer's technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products and patent research.
The technical proposal, after being agreed and approved in the prescribed manner, is the basis for the development of a preliminary (technical) design.
Scope of work - according to GOST 2.118-73.
(Revised edition, Rev. No. 1).
5. Draft design - a set of design documents that should contain fundamental design solutions that give a general idea of the device and the principle of operation of the product, as well as data that determine the purpose, main parameters and overall dimensions of the product being developed.
The draft design, after being agreed and approved in the prescribed manner, serves as the basis for the development of a technical project or working design documentation.
Scope of work - according to GOST 2.119-73.
6. Technical design - a set of design documents that must contain final technical solutions that give a complete picture of the design of the product being developed, and initial data for the development of working documentation.
The technical design, after being agreed and approved in the prescribed manner, serves as the basis for the development of working design documentation.
Scope of work - according to GOST 2.120-73.
7. Previously developed design documents are used in the development of new or modernization of manufactured products in the following cases:
a) in project documentation (technical proposal, draft and technical designs) and working documentation of a prototype (pilot batch) - regardless of the lettering of the documents used;
b) in the design documentation with the letters "O 1" ("O 2"), "A" and "B", if the lettering of the document used is the same or higher.
The lettering of a complete set of design documentation is determined by the lowest of the letters indicated in the documents included in the set, except for documents of purchased products.
(Revised edition, Rev. No. 1).
8. Design documents, the original holders of which are other enterprises, can only be used if there are registered copies or duplicates.
